Till sidans innehåll

Table Microphone Boom Arm

  • Aluminium construction
  • Locking centre joint
  • 5/8" threaded connector
  • Table clamp for up to max. 56 mm table thickness
  • Pre-wired with XLR cable
  • Length of upper arm: 43 cm
  • Length of lower arm: 40 cm
  • Maximum load capacity: 1.5 kg
  • Colour: Black
  • Tillgänglig sedan September 2018
  • Artikelnummer 437359
  • försäljningsenhet 1 Styck
  • Type Microphone Boom
  • Colour Black
  • Weight 1,8 kg
792 kr
Alla priser inklusive moms
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
1

157 Kundbetyg

4.2 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

stabilitet

hantverkskvalitet

103 Recensioner

R
Hur bra som helst
Roze 01.03.2021
Lite stiff i armen med annars är den hur bra som helst, det går att ändra hur lätt som helst och jag älskar att xlr kablen är inbyggd in armen, mycket mindre kablar att hålla reda på
hantverkskvalitet
stabilitet
0
0
Anmäl recension

Anmäl recension

F
Stabil och väl fungerande.
Fredrik6714 14.11.2020
Se ovan. =)
Jag har inte använt mikkabeln som finns inbyggd i stativet men själva stativet är bra.
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
P
not bad but room for improvement
PKristoffersson 13.02.2020
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
2
1
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
S
Disgusting Design Flaw – Avoid at All Costs
SmarttMark 22.06.2025
I deeply regret purchasing the Millenium DS200 Black mic arm. On the surface, it looks sturdy enough, but the design is absolutely appalling. If the wire goes—which it will, eventually—there is no accessible way to replace it unless you literally cut the wire with scissors and attempt to re-thread it. Why? Because the plug won’t fit through the internal path. This makes it essentially disposable once a fault occurs.

We’re not talking about a budget set of earbuds here. This is sold as a professional boom arm, yet it’s built like a cheap toy. A product that forces you to destroy and replace it within a few years if anything goes wrong is unacceptable. It’s the definition of bad engineering and poor sustainability.

If I could rate it zero stars for quality and stability, I would. Absolutely disgusted. Never again.
hantverkskvalitet
stabilitet
0
0
Anmäl recension

Anmäl recension